Invacare PRONTO R2-250 User Manual Page 15
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
15
F
R
O
N
T
R
I
G
G
I
N
G
S
PROCEDURE 3FRONT RIGGINGS
This Procedure Includes the Following:
Installing/Removing Footrests
Adjusting Footrest Height
Replacing Heel Loops
Installing/Removing Elevating Legrests
Raising/Lowering Elevating Legrests and/or
Adjusting Calfpads
Adjusting/Replacing Telescoping Front
Rigging Support
Adjusting Removable Footboard
Removing the Removable Footboard Assembly
from the Wheelchair
Installing/Removing the One Piece Footboard
Adjusting the One Piece Footboard - Height,
Angle and Depth
Removing/Installing the Calf-Pads
Adjusting the Calf-Pads
Footrest Angle Adjustments
Removing
1. Push the footrest release lever inward and rotate
the footrest outward.
2. Lift up on the footrest and remove from the wheel-
chair.
3. Repeat STEPS 1-2 for the opposite side of the wheel-
chair.
ADJUSTING FOOTREST HEIGHT
All Footrests Except Model P93M Footrests
(FIGURE 2)
1. Remove any accessory from the footrest(s).
2. Remove the footrest from the wheelchair. Refer to
INSTALLING/REMOVING FOOTRESTS in this pro-
cedure of the manual.
NOTE: Lay the footrest on a flat surface to simplify this
procedure.
3. Remove the hex bolt, coved washers and locknut
that secure the lower footrest to the footrest support.
4. Reposition the lower footrest to the desired height.
5. Reinstall the hex bolt, coved washers and locknut
that secure the lower footrest to the footrest support
and tighten securely.
6. Repeat STEPS 1-5 for the opposite side of the wheel-
chair footrest, if necessary.
7. Reinstall the footrest(s) onto the wheelchair. Refer
to
INSTALLING/REMOVING FOOTRESTS in this
procedure of the manual.
8. Reinstall any accessory onto the footrest(s).
FIGURE 1 - INSTALLING/REMOVING FOOTRESTS
Footrest
Hinge
Plate
Footrest
Release
Lever
Hinge
Pins
WARNING
After ANY adjustments, repair or service and BE-
FORE use, make sure all attaching hardware is
tightened securely - otherwise injury or damage
may result.
Wheelchair Frame
NOTE: Some footrests may require the use of two (2)
hands to install/remove from the wheelchair.
INSTALLING/REMOVING
FOOTRESTS (FIGURE 1)
Installing
1. Turn the footrest to the side (open footplate is
perpendicular to wheelchair) and position the
mounting holes in the footrest hinge plates with
the hinge pins on the wheelchair frame.
2. Install the footrest hinge plates onto the hinge pins
on the wheelchair frame.
3. Push the footrest towards the inside of the wheel-
chair until it locks into place.
NOTE: The footplate will be on the inside of the wheel-
chair when locked in place.
4. Repeat STEPS 1-3 for opposite side of wheelchair.
- R2-250 Series 1
- SPECIAL NOTES 2
- TABLE OF CONTENTS 3
- SPECIFICATIONS 4
- GENERAL WARNINGS 5
- PROCEDURE 1GENERAL GUIDELINES 7
- SAFETY/HANDLING OF 8
- WHEELCHAIRS 8
- GENERAL GUIDELINESPROCEDURE 1 10
- BATTERY BOX SHIPPING INSERTS 11
- SAFETY INSPECTION CHECKLIST 12
- TROUBLESHOOTING - ELECTRICAL 13
- TROUBLESHOOTING - MECHANICAL 13
- CHECKING BATTERY CHARGE LEVEL 13
- FOOTRESTS (FIGURE 1) 15
- ADJUSTING FOOTREST HEIGHT 15
- INSTALLING/REMOVING 15
- ELEVATING LEGRESTS (FIGURE 5) 16
- ADJUSTING REMOVABLE 18
- FOOTBOARD 18
- REMOVING THE REMOVABLE 19
- FOOTBOARD ASSEMBLY FROM 19
- THE WHEELCHAIR (FIGURE 11) 19
- ADJUSTING THE ONE PIECE 20
- FOOTBOARD - HEIGHT, ANGLE 20
- AND DEPTH 20
- INSTALLING/REMOVING THE ONE 20
- PIECE FOOTBOARD (FIGURE 12) 20
- REMOVING/INSTALLING THE 21
- CALF-PADS (FIGURE 16) 21
- ADJUSTING THE CALF-PADS 21
- FOOTREST ANGLE ADJUSTMENTS 26
- (FIGURE 23) 26
- INSTALLING/REMOVING FLIP BACK 27
- ARMRESTS (FIGURE 1) 27
- ADJUSTING FLIP BACK ARMRESTS 27
- (FIGURE 2) 27
- ADJUSTING CAPTAIN'S SEAT 28
- ARMRESTS 28
- PREPARING MKIV JOYSTICK FOR 30
- USE (FIGURE 1) 30
- REPOSITIONING MKIV JOYSTICK 30
- REPOSITIONING BATTERY 31
- CHARGER CONNECTOR (FIGURE 3) 31
- FUSE REPLACEMENT (FIGURE 4) 31
- REPLACING BATTERY BOX 32
- RETAINING STRAP (FIGURE 1) 32
- 3/4-inch Minimum 32
- ENGAGING/DISENGAGING MOTORS 33
- WITH MOTOR LOCKS (FIGURE 3) 33
- ADJUSTING FORKS (FIGURE 4) 34
- ADJUSTING THE STABILIZER 34
- (FIGURE 5) 34
- REMOVING/INSTALLING SHROUDS 35
- (FIGURE 1) 35
- REPLACING BACK OR HEADREST 36
- UPHOLSTERY (FIGURE 2) 36
- RECLINER OPERATION (FIGURE 1) 36
- ADJUSTING BACK OR HEADREST 37
- UPHOLSTERY (FIGURE 3) 37
- BATTERIES INTO/FROM BATTERY 38
- BOXES (FIGURE 1) 38
- CONNECTING BATTERY CABLES 39
- R2-250 Series 43
- TOOL QUANTITY COMMENTS 44
- Battery Charger 1 Supplied 44
- REPLACING BATTERIES 45
- INSTALLING/REMOVING BATTERY 45
- BOXES (FIGURE 9) 45
- LIMITED WARRANTY 47
Related products and manuals for Computer desks Invacare PRONTO R2-250
(44 pages)© 2020, manymanuals.com. All rights reserved. | 0.555 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals