Invacare PRONTO R2-250 User Manual Page 21
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
21
Depth (FIGURE 15)
1. Remove the four (4) flat head screws and barrel
nuts that secure the footboard to the two (2) half
clamps.
NOTE: The footboard depth may also be adjusted by
rotating the half clamp 180
o
.
2. Position the footboard on the two (2) half clamps
at the desired mounting position.
3. Install the four (4) flat head screws and barrel nuts
through the footboard and two (2) half clamps.
Securely Tighten.
FIGURE 15 - ADJUSTING THE FOOTBOARD ANGLE/DEPTH
FIGURE 14 - ADJUSTING THE FOOTBOARD ANGLE
Barrel Nuts
Flat Head
Screws
Mounting
Holes
Footboard
Heel
Half Clamp
SIDE VIEW OF 90
O
FOOTBOARD
Flat Head Screws
(Loosen Here)
Barrel Nuts
Pivot Hinge
Half Clamp mounting
positions
WARNING
DO NOT use these
mounting hole posi-
tions with the half
clamp in this orienta-
tion, otherwise injury
and/or damage may
result.
REMOVING/INSTALLING THE
CALF-PADS (FIGURE 16)
NOTE: Instructions apply to removing the calf-pads.
To install the calf-pads, reverse the following steps.
1. Remove the one piece footboard from the chair. Re-
fer to INSTALLING/REMOVING THE ONE PIECE
FOOTBOARD in this procedure of the manual.
2. Remove the two (2) phillips head screws and wash-
ers that secure the calf-pad to the calf-pad bracket.
3. Repeat for other calf-pad if necessary.
Calf-Pad
Calf-Pad Bracket
Washer
Phillips Head
Screws
FIGURE 16 - REMOVING/INSTALLING CALF-PADS
ADJUSTING THE CALF-PADS
NOTE: Some calf-pad adjustments may require the
removal of the one piece footboard. Refer to REMOV-
ING THE ONE PIECE FOOTBOARD in this procedure
of the manual.
Adjusting the Calf-Pad Height (FIGURE 17)
1. Remove the calf-pads. Refer to
REMOVING/IN-
STALLING THE CALF-PADS in this procedure of
the manual.
2. Remove the two (2) hub caps from the pivot bracket.
3. Remove the mounting bolt, locknut, two (2) caplug
washers and two (2) large washers that secure the
pivot bracket to the legrest tube.
NOTE: DO NOT cover the warning label on the legrest
tube shown in FIGURE 17.
4. Slide the calf assembly up or down to the desired
position on the legrest tube.
5. Secure pivot bracket to the legrest tube with the
mounting bolt, (2) caplug washers and two (2) large
washers and locknut. Securely tighten.
6. Replace the two (2) hub caps over the caplug wash-
ers.
7. If necessary, replace the one piece footboard. Re-
fer to
INSTALLING THE ONE PIECE FOOTBOARD
in this procedure of the manual.
F
R
O
N
T
R
I
G
G
I
N
G
S
FRONT RIGGINGS PROCEDURE 3
- R2-250 Series 1
- SPECIAL NOTES 2
- TABLE OF CONTENTS 3
- SPECIFICATIONS 4
- GENERAL WARNINGS 5
- PROCEDURE 1GENERAL GUIDELINES 7
- SAFETY/HANDLING OF 8
- WHEELCHAIRS 8
- GENERAL GUIDELINESPROCEDURE 1 10
- BATTERY BOX SHIPPING INSERTS 11
- SAFETY INSPECTION CHECKLIST 12
- TROUBLESHOOTING - ELECTRICAL 13
- TROUBLESHOOTING - MECHANICAL 13
- CHECKING BATTERY CHARGE LEVEL 13
- FOOTRESTS (FIGURE 1) 15
- ADJUSTING FOOTREST HEIGHT 15
- INSTALLING/REMOVING 15
- ELEVATING LEGRESTS (FIGURE 5) 16
- ADJUSTING REMOVABLE 18
- FOOTBOARD 18
- REMOVING THE REMOVABLE 19
- FOOTBOARD ASSEMBLY FROM 19
- THE WHEELCHAIR (FIGURE 11) 19
- ADJUSTING THE ONE PIECE 20
- FOOTBOARD - HEIGHT, ANGLE 20
- AND DEPTH 20
- INSTALLING/REMOVING THE ONE 20
- PIECE FOOTBOARD (FIGURE 12) 20
- REMOVING/INSTALLING THE 21
- CALF-PADS (FIGURE 16) 21
- ADJUSTING THE CALF-PADS 21
- FOOTREST ANGLE ADJUSTMENTS 26
- (FIGURE 23) 26
- INSTALLING/REMOVING FLIP BACK 27
- ARMRESTS (FIGURE 1) 27
- ADJUSTING FLIP BACK ARMRESTS 27
- (FIGURE 2) 27
- ADJUSTING CAPTAIN'S SEAT 28
- ARMRESTS 28
- PREPARING MKIV JOYSTICK FOR 30
- USE (FIGURE 1) 30
- REPOSITIONING MKIV JOYSTICK 30
- REPOSITIONING BATTERY 31
- CHARGER CONNECTOR (FIGURE 3) 31
- FUSE REPLACEMENT (FIGURE 4) 31
- REPLACING BATTERY BOX 32
- RETAINING STRAP (FIGURE 1) 32
- 3/4-inch Minimum 32
- ENGAGING/DISENGAGING MOTORS 33
- WITH MOTOR LOCKS (FIGURE 3) 33
- ADJUSTING FORKS (FIGURE 4) 34
- ADJUSTING THE STABILIZER 34
- (FIGURE 5) 34
- REMOVING/INSTALLING SHROUDS 35
- (FIGURE 1) 35
- REPLACING BACK OR HEADREST 36
- UPHOLSTERY (FIGURE 2) 36
- RECLINER OPERATION (FIGURE 1) 36
- ADJUSTING BACK OR HEADREST 37
- UPHOLSTERY (FIGURE 3) 37
- BATTERIES INTO/FROM BATTERY 38
- BOXES (FIGURE 1) 38
- CONNECTING BATTERY CABLES 39
- R2-250 Series 43
- TOOL QUANTITY COMMENTS 44
- Battery Charger 1 Supplied 44
- REPLACING BATTERIES 45
- INSTALLING/REMOVING BATTERY 45
- BOXES (FIGURE 9) 45
- LIMITED WARRANTY 47
Related products and manuals for Computer desks Invacare PRONTO R2-250
(44 pages)© 2020, manymanuals.com. All rights reserved. | 0.188 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals