Invacare PRONTO R2-250 User Manual Page 18
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
18
ADJUSTING REMOVABLE
FOOTBOARD
Depth (FIGURE 8)
1. Remove the four (4) flat head screws and barrel nuts
that secure the removable footboard to the two (2)
footplate clamps.
2. Move the removable footboard to one (1) of the four
(4) positions.
3. Reinstall the four (4) flat head screws and barrel nuts
that secure the removable footboard to the two (2)
footplate clamps. Tighten securely.
F
R
O
N
T
R
I
G
G
I
N
G
S
FRONT RIGGINGSPROCEDURE 3
Footplate
Clamp
Removable
Footboard
FIGURE 8 - ADJUSTING FLIP-UP
REMOVABLE FOOTBOARD - DEPTH
Mounting
Positions
Flat Head Screws
Barrel Nut
Barrel Nut
Angle (FIGURE 9)
1. Loosen, but do not remove, the four (4) flat head
screws and barrel nuts that secure the removable
footboard to the two (2) footplate clamps.
NOTE: Because of the two (2) support tubes, the
angle of the removable footboard can be adjusted
downward ONLY.
2. Grasp the front of the removable footboard and ro-
tate it DOWNWARD until the desired angle is
reached.
3. While holding the removable footboard in place,
tighten the four (4) flat head screws and barrel nuts
securely.
FIGURE 9 - ADJUSTING FLIP-UP REMOVABLE
FOOTBOARD - ADJUSTING FOOTBOARD ANGLE
Removable
Footboard
Barrel Nut
Flat
Head
Screw
Angle Can Be Adjusted
Downward ONLY
FRONT
Footplate
Clamp
Height (FIGURE 10)
1. Remove the removable footboard plate. Refer to
REMOVING THE REMOVEABLE FOOTBOARD
ASSEMBLY FROM THE WHEELCHAIR in this pro-
cedure of the manual.
2. Remove the caplug cap.
3. Remove the mounting screw, caplug washer, flat
washer and nut that secures the two (2) large wash-
ers and support tube to the height adjustment
bracket and footboard bracket. Refer to DETAIL
“A”.
4. Remove the nut, flat washer and that secure the
threaded arm on the height adjustment bracket to
the footboard bracket. Refer to DETAIL “B”.
5. Move the height adjustment bracket to one (1) of
seven (7) height positions.
6. Reinstall the flat washer and nut that secures the
threaded arm on the height adjustment bracket to
the footboard bracket. Refer to DETAIL “B”.
7. Reinstall the mounting screw, caplug washer, flat
washer and nut that secures the two (2) large
washers and support tube to the height adjust-
ment bracket and footboard bracket. Refer to
DETAIL “A”.
8. Reinstall the caplug caps.
9. Repeat STEPS 2-8 for the opposite footboard
bracket.
10. Reinstall the removable footboard plate. Refer to
REMOVING THE REMOVEABLE FOOTBOARD
ASSEMBLY FROM THE WHEELCHAIR in this pro-
cedure of the manual.
- R2-250 Series 1
- SPECIAL NOTES 2
- TABLE OF CONTENTS 3
- SPECIFICATIONS 4
- GENERAL WARNINGS 5
- PROCEDURE 1GENERAL GUIDELINES 7
- SAFETY/HANDLING OF 8
- WHEELCHAIRS 8
- GENERAL GUIDELINESPROCEDURE 1 10
- BATTERY BOX SHIPPING INSERTS 11
- SAFETY INSPECTION CHECKLIST 12
- TROUBLESHOOTING - ELECTRICAL 13
- TROUBLESHOOTING - MECHANICAL 13
- CHECKING BATTERY CHARGE LEVEL 13
- FOOTRESTS (FIGURE 1) 15
- ADJUSTING FOOTREST HEIGHT 15
- INSTALLING/REMOVING 15
- ELEVATING LEGRESTS (FIGURE 5) 16
- ADJUSTING REMOVABLE 18
- FOOTBOARD 18
- REMOVING THE REMOVABLE 19
- FOOTBOARD ASSEMBLY FROM 19
- THE WHEELCHAIR (FIGURE 11) 19
- ADJUSTING THE ONE PIECE 20
- FOOTBOARD - HEIGHT, ANGLE 20
- AND DEPTH 20
- INSTALLING/REMOVING THE ONE 20
- PIECE FOOTBOARD (FIGURE 12) 20
- REMOVING/INSTALLING THE 21
- CALF-PADS (FIGURE 16) 21
- ADJUSTING THE CALF-PADS 21
- FOOTREST ANGLE ADJUSTMENTS 26
- (FIGURE 23) 26
- INSTALLING/REMOVING FLIP BACK 27
- ARMRESTS (FIGURE 1) 27
- ADJUSTING FLIP BACK ARMRESTS 27
- (FIGURE 2) 27
- ADJUSTING CAPTAIN'S SEAT 28
- ARMRESTS 28
- PREPARING MKIV JOYSTICK FOR 30
- USE (FIGURE 1) 30
- REPOSITIONING MKIV JOYSTICK 30
- REPOSITIONING BATTERY 31
- CHARGER CONNECTOR (FIGURE 3) 31
- FUSE REPLACEMENT (FIGURE 4) 31
- REPLACING BATTERY BOX 32
- RETAINING STRAP (FIGURE 1) 32
- 3/4-inch Minimum 32
- ENGAGING/DISENGAGING MOTORS 33
- WITH MOTOR LOCKS (FIGURE 3) 33
- ADJUSTING FORKS (FIGURE 4) 34
- ADJUSTING THE STABILIZER 34
- (FIGURE 5) 34
- REMOVING/INSTALLING SHROUDS 35
- (FIGURE 1) 35
- REPLACING BACK OR HEADREST 36
- UPHOLSTERY (FIGURE 2) 36
- RECLINER OPERATION (FIGURE 1) 36
- ADJUSTING BACK OR HEADREST 37
- UPHOLSTERY (FIGURE 3) 37
- BATTERIES INTO/FROM BATTERY 38
- BOXES (FIGURE 1) 38
- CONNECTING BATTERY CABLES 39
- R2-250 Series 43
- TOOL QUANTITY COMMENTS 44
- Battery Charger 1 Supplied 44
- REPLACING BATTERIES 45
- INSTALLING/REMOVING BATTERY 45
- BOXES (FIGURE 9) 45
- LIMITED WARRANTY 47
Related products and manuals for Computer desks Invacare PRONTO R2-250
(44 pages)© 2020, manymanuals.com. All rights reserved. | 0.173 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals