Invacare PRONTO R2-250 User Manual Page 39
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
39
PROCEDURE 11BATTERIES
B
A
T
T
E
R
I
E
S
CONNECTING BATTERY CABLES
WARNING
NEVER allow any of your tools and/or battery
cable(s) to contact BOTH battery terminal(s)/post(s)
at the same time. An electrical short may occur
and serious personal injury or damage may occur.
The use of rubber gloves and safety glasses is rec-
ommended when working with batteries.
Dual U1 or Dual Group 22 NF Battery Boxes
Perform one (1) of the following methods for connect-
ing the battery cable(s):
A. FOR DUAL U1 BATTERIES - Use direct mount
method. Refer to FIGURES 2 AND 3.
B. FOR DUAL GROUP 22 NF BATTERIES THAT
HAVE MOUNTING HOLES IN THE BATTERY
TERMINAL(S)/POST(S) - Use direct mount
method. Refer to FIGURES 2 AND 3.
C. FOR DUAL GROUP 22 NF BATTERIES THAT
DO NOT HAVE MOUNTING HOLES IN THE
BATTERY TERMINAL(S)/POST(S) - Use battery
clamp method. Refer to FIGURES 4, 5 AND 6.
DIRECT MOUNT METHOD (FIGURE 2 AND 3).
1. Install battery terminal cap(s) onto battery cable(s) as
follows (FIGURE 2):
DUAL U1 BATTERIES:
A. ORANGE battery terminal cap onto RED battery
cable.
B. GRAY battery terminal cap onto BLACK battery
cable.
DUAL GROUP 22 NF BATTERIES:
A. RED battery terminal cap onto RED battery cable.
B. BLACK battery terminal cap onto BLACK bat-
tery cable.
FIGURE 2 - CONNECTING BATTERY CABLES -
DIRECT MOUNT METHOD
CAUTION
When connecting the battery cables to the
battery(ies), the battery cable(s) MUST be con-
nected to the battery terminal(s)/post(s) as
shown in DETAIL “A” or DETAIL “B” of FIGURE 3
(depending on battery type), otherwise dam-
age to the battery cable may result when in-
stalling battery terminal caps.
2. Connect battery cable(s) to battery(ies) terminal(s)/
post(s) as follows (DETAIL “A” or DETAIL “B” of
FIGURE 3, depending on battery type):
A. NEGATIVE (-) BLACK battery cable to NEGA-
TIVE (-) battery terminal/post.
B. POSITIVE (+) RED battery cable to POSITIVE
(+) battery terminal/post.
3. Secure the battery cable(s)/ring terminal(s) to the
battery terminal(s)/post(s), BLACK to NEGATIVE
(-) and RED to POSITIVE (+), with the provided 1/
4-20 x 7/8-inch hex flange screw and hex flange
locknut. Securely tighten. (DETAIL “A” or DETAIL
“B” of FIGURE 3, depending on battery type).
4. Verify all battery cable(s)/ring terminal(s) are correctly
installed and securely tightened.
5. Slide terminal cap(s) down battery cable(s) and onto
battery clamps (FIGURE 3).
6. Secure each terminal cap in place with a tie-wrap
(Use tie-wraps 11-1/2-inches long) (FIGURE 3).
NOTE: It will be necessary to trim excess tie-wrap in order to
install the battery box top(s).
7. Install the battery box top(s).
8. Install the battery box(es) into the wheelchair. Refer
to
INSTALLING/REMOVING BATTERY BOX(ES) in
this procedure of the manual.
NOTE: New Battery(ies) MUST be fully charged BEFORE
using, otherwise the life of the battery(ies) will be reduced.
9. If necessary, charge the battery(ies). Refer to
CHARGING BATTERIES in this procedure of the
manual.
Battery Cable
Battery Terminal
Cap
NOTE: Only one (1) battery cable and terminal cap shown
for clarity. Both caps install in the same manner.
INSTALLING BATTERY TERMINAL CAPS
- R2-250 Series 1
- SPECIAL NOTES 2
- TABLE OF CONTENTS 3
- SPECIFICATIONS 4
- GENERAL WARNINGS 5
- PROCEDURE 1GENERAL GUIDELINES 7
- SAFETY/HANDLING OF 8
- WHEELCHAIRS 8
- GENERAL GUIDELINESPROCEDURE 1 10
- BATTERY BOX SHIPPING INSERTS 11
- SAFETY INSPECTION CHECKLIST 12
- TROUBLESHOOTING - ELECTRICAL 13
- TROUBLESHOOTING - MECHANICAL 13
- CHECKING BATTERY CHARGE LEVEL 13
- FOOTRESTS (FIGURE 1) 15
- ADJUSTING FOOTREST HEIGHT 15
- INSTALLING/REMOVING 15
- ELEVATING LEGRESTS (FIGURE 5) 16
- ADJUSTING REMOVABLE 18
- FOOTBOARD 18
- REMOVING THE REMOVABLE 19
- FOOTBOARD ASSEMBLY FROM 19
- THE WHEELCHAIR (FIGURE 11) 19
- ADJUSTING THE ONE PIECE 20
- FOOTBOARD - HEIGHT, ANGLE 20
- AND DEPTH 20
- INSTALLING/REMOVING THE ONE 20
- PIECE FOOTBOARD (FIGURE 12) 20
- REMOVING/INSTALLING THE 21
- CALF-PADS (FIGURE 16) 21
- ADJUSTING THE CALF-PADS 21
- FOOTREST ANGLE ADJUSTMENTS 26
- (FIGURE 23) 26
- INSTALLING/REMOVING FLIP BACK 27
- ARMRESTS (FIGURE 1) 27
- ADJUSTING FLIP BACK ARMRESTS 27
- (FIGURE 2) 27
- ADJUSTING CAPTAIN'S SEAT 28
- ARMRESTS 28
- PREPARING MKIV JOYSTICK FOR 30
- USE (FIGURE 1) 30
- REPOSITIONING MKIV JOYSTICK 30
- REPOSITIONING BATTERY 31
- CHARGER CONNECTOR (FIGURE 3) 31
- FUSE REPLACEMENT (FIGURE 4) 31
- REPLACING BATTERY BOX 32
- RETAINING STRAP (FIGURE 1) 32
- 3/4-inch Minimum 32
- ENGAGING/DISENGAGING MOTORS 33
- WITH MOTOR LOCKS (FIGURE 3) 33
- ADJUSTING FORKS (FIGURE 4) 34
- ADJUSTING THE STABILIZER 34
- (FIGURE 5) 34
- REMOVING/INSTALLING SHROUDS 35
- (FIGURE 1) 35
- REPLACING BACK OR HEADREST 36
- UPHOLSTERY (FIGURE 2) 36
- RECLINER OPERATION (FIGURE 1) 36
- ADJUSTING BACK OR HEADREST 37
- UPHOLSTERY (FIGURE 3) 37
- BATTERIES INTO/FROM BATTERY 38
- BOXES (FIGURE 1) 38
- CONNECTING BATTERY CABLES 39
- R2-250 Series 43
- TOOL QUANTITY COMMENTS 44
- Battery Charger 1 Supplied 44
- REPLACING BATTERIES 45
- INSTALLING/REMOVING BATTERY 45
- BOXES (FIGURE 9) 45
- LIMITED WARRANTY 47
Related products and manuals for Computer desks Invacare PRONTO R2-250
(44 pages)© 2020, manymanuals.com. All rights reserved. | 0.655 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals